FAQs Archive - Page 7 of 8

AMERICAS	EUROPE	APAC
USA Canada Commercial Products Canada Residential Products Latin America	International	China Malaysia Taiwan Thailand South Korea Vietnam Hongkong Indonesia Australia

I have a Huebsch electric dryer model HDE107WF. My customers are complaining that it doesn’t get hot enough. Most loads are not dry in one cycle. I have checked the duct and it is clear. What else can be done?

Huebsch Team2019-05-01T09:46:58+00:00May 1st, 2019|

How long does the vent run and how many 90 degree elbows are present? Also, what type of venting material is used? If the "slinky" type flexible venting is used, it can be causing back pressure even though the vent

How can I get a copy of the schematics?

Huebsch Team2019-05-01T09:46:02+00:00May 1st, 2019|

All washers have a removable top panel for service. The wiring diagram is located in a plastic bag on the right-handed side of the unit. The top needs to be unlocked and tipped up to access the diagram.

My store uses Huebsch dryers, model JT0300DFG. I am having an issue. Sometimes when I put coins into the machine, it doesn’t work and the symbol “ERR” displays and blinks. Other times that symbol is gone and returns to normal status.

Huebsch Team2019-05-01T09:44:51+00:00May 1st, 2019|

The coin drop is dirty. Remove, take apart and remove all the lint. If the issue continues replace the drop.

We have a model #JT0350SEL-ser#R0009000117. It shuts off one second after starting. We have cleaned the entire machine but it appears the air flow switch is tripping out. Any suggestions?

Huebsch Team2019-05-01T09:43:36+00:00May 1st, 2019|

If the air flow switch is opening as stated then there is a major restriction in the exhaust system, the fan is not operating, there is a plugged lint filter or there is a major air leak between the cylinder

I have Huebsch dryers and the back of the drums are all turning brown. It looks like it is scorched from the use of fabric softeners. What is the best way to clean it?

Huebsch Team2019-05-01T09:41:51+00:00May 1st, 2019|

Some 409 cleaner and a Brillo pad will remove the excess softener build up.

We have MDC top load DOE washing machines in our laundry rooms. There are either three or four machines in each laundry room. We are looking to replace the existing hot water tanks with tankless hot water units. The suppliers are not certain of the size of tankless unit to supply either the three or four machine scenario. Can you advise me on the correct tankless sized unit?

Huebsch Team2019-05-01T09:42:27+00:00May 1st, 2019|

The estimated hot water usage is 16 gallons per cycle per washer and the cycle time is 34 minutes. You will need to use this info to calculate heater size.

I am in the process of buying a coin laundry and I would like to know how much water a Huebsch 27 lb, model HC27 uses, as well as a 35 lb, model JTO300drg.

Huebsch Team2019-05-01T09:22:02+00:00May 1st, 2019|

1) Water consumption is dependent on the programmed number of baths and the programmed water levels. The Huebsch HC27 washer you mention is at least 10 years old and probably has a mechanical timer. Water consumption for a regular cycle

Is there a specific type of PDA required to use the Galaxy control on Huebsch machines?

Huebsch Team2019-05-01T09:59:35+00:00May 1st, 2019|

The PDA has to run Microsoft Windows Mobile 2003 or greater in order to work with the Galaxy software. Your Huebsch distributor can provide you a list of tested PDA models.

What is the cost of electricity for drying a 30 lb wash load?

Huebsch Team2019-05-01T09:20:02+00:00May 1st, 2019|

This is a good estimate, but your results will vary: Assumptions: 30 lb dry weight load of cotton towels, 100G washer-extractor, dried in 45 lb natural gas tumbler Electricity cost = $0.12/kWH, natural gas cost = $1.00/therm Huebsch Dryer Energy

I have a 20 lb washer, model #HC20BC20V6001. I would like to know how I can change the amount charged, and is there any sequence used in order to give a free wash with out having to open the machine. We are using control system 0231589-1*.

Huebsch Team2019-05-01T09:18:35+00:00May 1st, 2019|

Since you have a B-Control machine, the machine has to be programmed manually and the machine has to be opened briefly to get into manual programming mode. Once you are in programming mode it is very easy to change the

Previous 678 Next