FAQs Archive - Page 2 of 4 - Huebsch

My store uses Huebsch dryers, model JT0300DFG. I am having an issue. Sometimes when I put coins into the machine, it doesn’t work and the symbol “ERR” displays and blinks. Other times that symbol is gone and returns to normal status.

Huebsch Team2019-05-01T09:44:51+00:00May 1st, 2019|Service/Maintenance Questions|

The coin drop is dirty. Remove, take apart and remove all the lint. If the issue continues replace the drop.

We have a model #JT0350SEL-ser#R0009000117. It shuts off one second after starting. We have cleaned the entire machine but it appears the air flow switch is tripping out. Any suggestions?

Huebsch Team2019-05-01T09:43:36+00:00May 1st, 2019|Service/Maintenance Questions|

If the air flow switch is opening as stated then there is a major restriction in the exhaust system, the fan is not operating, there is a plugged lint filter or [...]

I have Huebsch dryers and the back of the drums are all turning brown. It looks like it is scorched from the use of fabric softeners. What is the best way to clean it?

Huebsch Team2019-05-01T09:41:51+00:00May 1st, 2019|Service/Maintenance Questions|

Some 409 cleaner and a Brillo pad will remove the excess softener build up.

We have MDC top load DOE washing machines in our laundry rooms. There are either three or four machines in each laundry room. We are looking to replace the existing hot water tanks with tankless hot water units. The suppliers are not certain of the size of tankless unit to supply either the three or four machine scenario. Can you advise me on the correct tankless sized unit?

Huebsch Team2019-05-01T09:42:27+00:00May 1st, 2019|Service/Maintenance Questions|

The estimated hot water usage is 16 gallons per cycle per washer and the cycle time is 34 minutes. You will need to use this info to calculate heater size.

I am in the process of buying a coin laundry and I would like to know how much water a Huebsch 27 lb, model HC27 uses, as well as a 35 lb, model JTO300drg.

Huebsch Team2019-05-01T09:22:02+00:00May 1st, 2019|Product Questions|

1) Water consumption is dependent on the programmed number of baths and the programmed water levels. The Huebsch HC27 washer you mention is at least 10 years old and probably has [...]

Is there a specific type of PDA required to use the Galaxy control on Huebsch machines?

Huebsch Team2019-05-01T09:59:35+00:00May 1st, 2019|Product Questions|

The PDA has to run Microsoft Windows Mobile 2003 or greater in order to work with the Galaxy software. Your Huebsch distributor can provide you a list of tested PDA models.

What is the cost of electricity for drying a 30 lb wash load?

Huebsch Team2019-05-01T09:20:02+00:00May 1st, 2019|Product Questions|

This is a good estimate, but your results will vary: Assumptions: 30 lb dry weight load of cotton towels, 100G washer-extractor, dried in 45 lb natural gas tumbler Electricity cost = [...]

I have a 20 lb washer, model #HC20BC20V6001. I would like to know how I can change the amount charged, and is there any sequence used in order to give a free wash with out having to open the machine. We are using control system 0231589-1*.

Huebsch Team2019-05-01T09:18:35+00:00May 1st, 2019|Product Questions|

Since you have a B-Control machine, the machine has to be programmed manually and the machine has to be opened briefly to get into manual programming mode. Once you are in [...]

I recently bought a Huebsch washer and I’m very satisfied by its performance. However, I was wondering if I can rinse the laundry with warm water instead of only with cold water? Model number: ZWN311SP111CW01 Serial number: 1107008829 Load size: 16 pounds

Huebsch Team2019-05-01T09:15:28+00:00May 1st, 2019|Product Questions|

The washer was designed to meet the Canadian Office on Energy Efficiency requirements and to do so it can not offer a warm rinse.

We have a new #HWTT20WN washing machine in a commercial building. The plumbing code requires external backflow preventers on the water piping, unless the washer has an internal air gap conforming to ASSE 1007. Does this washing machine have an internal air gap conforming to ASSE 1007?

Huebsch Team2019-05-01T09:14:08+00:00May 1st, 2019|Product Questions|

Yes, our UL Safety Certification for Clothes Washers requires testing and reviews to the standard UL2157, which includes a section on plumbing. This cites that the washer does comply with ASSE [...]