The most we can say about the unit is that it’s probably designed as a 50-pound tumbler. Our best guess is that it was built in the 1960’s.

Mining will need a heavy soil cycle, which is a 45 minute cycle. The light soil cycle time is about 30 minutes.

Temperature is completely input dependent on standard no heat models. Cold water input varies greatly by geography and time of year. Hot water heater temperature setting is also highly variable dependent on market and application.

Cold cycle = all cold water input
Warm cycle = half hot and half cold
Hot cycle = all hot water

The first bath will be significantly affected by the temperature of the load. Each subsequent bath will be affected a few degrees by the previous bath if a different temperature is selected or affected very little if the same temperature is used. Over the bath time, the water will also move a few degrees toward ambient room temperature.

Because you are doing heavy soiled loads you will need hot water. If you assume half hot and half cold, measure your input temperatures and take an average and that should get you in the ballpark. There is no way to give you a reliable number without specific temps, specific cycle, actual load size, ambient temp, etc.

The MEA number used to be required by New York City. The building code has since been revised to state that MEA approvals were not required if the product was certified by a National Recognized Test Lab (NRTL).

All of our equipment is CSA approved which is the equivalent of UL (both are certified NRTLs).

For a 35-lb tumbler the gas consumption per load is 34,853 BTUs which is $0.383 per load (assumes average cost of natural gas at $1.10 per therm). Energy to run the motors and control is approximately $0.025 per load (assumes $0.065 per kWh of electricity).

Therefore, the total cost per load is approximately $0.41 per load.

The answer to this question can get a little tricky since variables come into play beyond our control, such as wetness of the load, size of the load and time set on the control.

Motors are not interchangeable between phases. The machine you are purchasing will only work on three-phase power.

There are many variables to water use. How the owner programs the machine and which cycles are selected by end users will change consumption. The best we can do is provide an estimate based on a commonly used cycle.

For the HCs, we can give data for current Galaxy 400/600 controlled models, factory default normal warm cycle, 80 percent load. This data is gallons per cycle (not per hour). A cycle takes approximately 26 minutes. Daily water use will depend on cycles (or ‘turns’) per day.

20 lb = 20 gal
30 lb = 28 gal
40 lb = 34 gal
60 lb = 45 gal
80 lb = 63 gal

For the stack, there is a testing procedure dictated by the U.S. Department of Energy, J1 testing, which uses a defined load and calculates the averages. Based on this testing, the washer part of the stack washer and dryer uses an average of 13.9 gallons per cycle which takes approximately 30 to 44 minutes depending on the cycle selected.

For a 35lb tumbler—gas consumption per load is 34,853 Btus which is 0.383 cents per load (assumes average cost of natural gas at $1.10 per Therm). Energy to run the motors and control is approximately 0.025 cents per load (assumes 0.065 cents per kWh electricity).

Total cost per load—approximately 0.41 cents.

The answer to this question can get a little tricky, though. Variables come into play beyond our control. Wetness of the load, size of the load and time set on the control. (It takes 25 minutes to dry a common load in this tumbler).

The recommended temperature for the water heater is 130 degrees Fahrenheit.

Yes, our UL Safety Certification for Clothes Washers requires testing and reviews to the standard UL2157, which includes a section on plumbing. This cites that the washer does comply with ASSE 1007.

The washer was designed to meet the Canadian Office on Energy Efficiency requirements and to do so it can not offer a warm rinse.

Since you have a B-Control machine, the machine has to be programmed manually and the machine has to be opened briefly to get into manual programming mode. Once you are in programming mode it is very easy to change the vend price.

This is a good estimate, but your results will vary:
Assumptions:

• 30 lb dry weight load of cotton towels, 100G washer-extractor, dried in 45 lb natural gas tumbler
• Electricity cost = $0.12/kWH, natural gas cost = $1.00/therm

Huebsch Dryer Energy cost for the 30 lb load:

• Total energy cost to dry = $0.52*
  *$0.46 for natural gas and $0.06 for electricity

If you dry with an electric heated tumble dryer as the question states, it is much more expensive, typically two to three times the total energy cost of a natural gas heated drying tumbler. For this financial reason, almost no vended laundries use electric heat drying tumblers.

The PDA has to run Microsoft Windows Mobile 2003 or greater in order to work with the Galaxy software. Your Huebsch distributor can provide you a list of tested PDA models.

1) Water consumption is dependent on the programmed number of baths and the programmed water levels. The Huebsch HC27 washer you mention is at least 10 years old and probably has a mechanical timer. Water consumption for a regular cycle is approximately 62 gallons of water per cycle – 10 gallons of hot water and 52 gallons of cold water. The comparable 35-pound capacity washer uses 102 gallons of water per cycle.

Huebsch washers have gone through a lot of changes in the last 10 years. All models now use the new Galaxy Control which offers tremendous flexibility for the owner. This includes the ability to control water levels and to charge a higher vend depending on the number of baths requested. By default, a Huebsch Galaxy 600 – 30 lb capacity washer-extractor uses just 26 gallons of water. Now would be a good time to consider replacing those 10+ year old machines.

Current Huebsch washer-extractors ship with water usage of approximately 0.8 gallons per rated pound capacity using a three bath cycle.

Approximate electrical power usage per load = 0.13 kWH per load for the SC27 and 0.21 kWh per load for the SC35.

2) If you have not done so, get the current sewer and energy bills for the laundromat to verify actual consumption.

3) A drying tumbler model (JT0300) was referenced at the bottom. Dryer gas consumption is highly dependent on the washer G-Force, the amount of make-up air provided and the venting.

JT0300s are very efficient compared to other dryers built at that time. If you assure the drying tumblers have sufficient make-up air, have been maintained and cleaned of lint, and that the exhaust system is clean and correctly installed you will have completed the most important steps to obtain fast drying and lower energy cost.